In 1938, New Hampshire highway officials tried an experiment to keep the roads clear during the winter. At the time, crews normally spread sand or cinders for traction while plowing, but New Hampshire authorities had another idea: spread salt instead to melt snow and ice. Road crews were already mixing salt into sand piles to keep them from freezing, so why not use salt on the pavement?

By the winter of 1941 and 1942, about 5,000 tons of road salt went down on highways nationwide. Over the years, states and municipalities came to see salt as the most effective and budget-friendly way to clear their roadways, according to a 1991 Transportation Research Board report. Today, highway deicing in the United States uses roughly 16 million metric tons of salt a year, based on 2025 figures from the USGS.

Although salt makes winter driving safer, it also clings to the undercarriage of your vehicle. Combine that with the liquid brines used today, and the risk of corrosion increases, with brake lines, fuel tanks, and exhaust systems being the most susceptible. To combat this, an undercarriage car wash should be part of your normal routine, especially during the winter.

Below, we explain what road salt does to underbody components and walk through how to safely clean the undercarriage of your car or truck at home.

What is an Undercarriage?

The undercarriage is another way to say the underside of your vehicle, or everything you would see if you slid beneath it on a creeper. Under your car or truck, you will find the floor pan, suspension, axles, exhaust system, fuel tank, and the brake and fuel lines.

Most cars and crossovers have a unibody construction, where the body and frame are one piece. Pickup trucks and some larger SUVs typically ride on a separate steel frame with rails and crossmembers, a design known as body-on-frame, which can translate to higher towing capacities.

In either case, because the undercarriage is closest to the road, it takes the brunt of the snow, slush, and salt as you drive.

What Road Salt Does to Your Vehicle’s Undercarriage

Steel rusts when it reacts with water and oxygen, a process that involves the movement of electrons. Electrons move more easily in saltwater, so any salty slush you drive through during the winter speeds up corrosion.

Since salt lowers the freezing point of water, the slush on your car’s undercarriage stays liquid at temperatures where plain water would freeze. Any leftover salt in that slush can settle in the nooks and crannies of your undercarriage, eating away at your vehicle over time.

Many road agencies now pre-treat pavement with liquid brines made from sodium, magnesium, or calcium chloride, which your tires spray underneath your vehicle. A 2010 University of Maine study, cited in a 2014 Connecticut Office of Legislative Research report, found that all chlorides cause corrosion, with calcium and magnesium chloride being “particularly corrosive because of their ability to retain moisture.”

Why Truck Undercarriages Need Extra Attention

Boxed frame rails on body-on-frame trucks can trap salt and moisture in hard-to-see, hard-to-reach areas. Brake and fuel lines, the spare tire, and the receiver hitch are among the components sitting in the “spray zone,” where your tires kick up the most snow, slush, and salt.

Left unchecked, rust on brake and fuel components can become a safety risk, according to AAA. If you see rust flaking or peeling off the metal under your vehicle, our guide on how to fix rust on a car walks through your repair options.

Work trucks, service vans, and other fleet vehicles see heavier use than the average car or crossover, which puts additional strain on underbody components. Towing and hauling heavy equipment to and from the job site may require driving on unpaved roads where rocks and gravel can chip protective coatings, leaving bare metal exposed to winter salt. If you drive a vehicle like this, regular undercarriage washes help remove excess salt.

Does an Undercarriage Wash Prevent Rust?

An undercarriage wash won’t make your vehicle rust-proof or undo damage that has already started. However, it slows corrosion by removing salt before it has time to settle in. Get in the habit of washing your vehicle regularly through the winter, including the undercarriage, to flush away salt and brine.

If you are working in your driveway, it’s possible that regular water from a garden hose or portable pressure washer may not remove everything. Road salt and brines are chloride compounds that leave a residue that water alone may struggle to remove. Using a salt neutralizer (covered more below) can help, as it’s designed to break down those deposits.

Do Automatic Car Washes Clean the Undercarriage?

Many automatic car washes have underbody sprays in their tunnel systems, but they may not be included in the basic package. If you are interested in a monthly membership, double-check which tier includes the undercarriage flush.

An automatic wash may not reach every part of your undercarriage or blast away all the caked-on mud from a hunting or camping trip to the north forty. Washing at home a few times a year gives you some flexibility and lets you target those stubborn spots.

Here in the Detroit area, I subscribe to a monthly plan at a local place that includes unlimited washes, an undercarriage flush on the conveyor, and tire shine. When I am pressed for time, it helps me keep up with regular washes. Once I get back home, I will use a detailing kit to put the finishing touches on everything.  

How to Clean the Undercarriage of a Car or Truck at Home

Gather these items before you start:

  • Stiff-bristled brush.

  • Safety glasses and gloves.

  • Garden hose or pressure washer.

  • Salt neutralizer or vehicle-safe cleaner.

  • Undercarriage water broom or angled wand attachment.

  • Ramps, or a floor jack and jack stands, plus wheel chocks.

Prep and Raise Your Vehicle Safely

Pick a day when temperatures are above freezing, aiming to wash in the late morning or early afternoon so your vehicle has time to dry before temperatures drop after sunset (it will also give your driveway time to dry).

Your vehicle might ride high enough that you can reach the undercarriage as-is. Should you need more clearance, start with these two important things first:

  • Check weight ratings: Confirm your ramps, floor jack, and jack stands are rated for your vehicle’s weight.

  • Find a level concrete surface: Avoid grass or slopes to minimize the chances of the ramps or jack stands slipping.

How to Use a Ramp to Raise Your Vehicle

If you are using ramps, follow these steps:

  • Line up the ramps: Place them straight ahead of the front tires.

  • Drive up slowly: Stop when you reach the cradle at the top. Have a neighbor or family member guide you from the side.

  • Secure your vehicle: Put it in Park (or in gear for a manual transmission) and set the parking brake.

  • Chock the wheels: Place wheel chocks around the rear tires since they will remain on the ground.

How to Use a Floor Jack and Jack Stands

If you are using a floor jack and jack stands, follow these steps. Remember that floor jacks are designed to lift a vehicle, not hold it up. Be sure to have both the jack and the jack stands before proceeding.

  • Secure and chock: Put your vehicle in Park, set the parking brake, and chock the wheels that will stay on the ground.

  • Confirm jacking points: Check your owner’s manual for the correct points (hybrid and EV manuals usually show how to avoid the battery pack).

  • Raise your vehicle: Lift slowly with the floor jack until it’s slightly higher than you need.

  • Position the jack stands: Slide the stands under the support points listed in your owner’s manual. Set both to the same height.

  • Lower onto the stands: Slowly release the jack’s valve until your vehicle rests fully on the stands. Raise the jack back up until it touches the frame or jacking point, without lifting, so it can catch your vehicle if a stand slips. Give your vehicle a firm push from the side to make sure it doesn’t move.

Person pressure washing underneath a vehicle, partially visible between the tires, with plants in the background.

Wash in Sections

Once you are under your vehicle, working in sections makes the job more manageable and reduces the chances of missing a spot or having the cleaning solution dry. Use these steps to guide you:

  • Rinse the wheel wells: Knock loose any mud, slush, and salt.

  • Apply the salt neutralizer: Mix it according to the label, then apply it with a hose-end or pump sprayer. Let it sit for the time listed on the label, but don’t let it dry.

  • Make a mental checklist: Key areas to wash include the frame rails and crossmembers, around the tires, and around the front and rear suspension. Wash around the fenders, the receiver hitch, and the spare tire if applicable. Use a stiff-bristled brush where needed.  

If your vehicle has a skid plate, consider removing it to wash away any trapped or hidden debris. Be mindful of brake lines, wiring connectors, sensors, and CV boots (the rubber covers on the axles), as high-pressure or forceful washing can damage them.

Rinse and Dry

Finish with a clean water rinse, working front to back to wash away any remaining cleaner or neutralizer.

Before lowering your vehicle, take a few minutes to inspect the undercarriage while you have a clear view. Make note of fluid leaks, corroded brake or fuel lines, and any other damage.

If you used jack stands, use the floor jack to lift your vehicle slightly off the stands. Remove the stands, gently lower your vehicle back to the ground, and remove the wheel chocks. If you used ramps, remove the wheel chocks before backing down slowly. Take a short drive to dry off excess water, tapping the brakes lightly to dry the rotors.  

Best Ways to Protect the Undercarriage of Your Car or Truck

Oil-based sprays and rubberized coatings put a barrier between bare metal and road salt. Before applying either, let the undercarriage dry completely after washing, which may take longer than your initial drive. In general, oil-based products are reapplied annually, while rubberized coatings work best on newer vehicles without rust, since spraying them over existing rust can trap moisture underneath.

Beyond sprays and coatings, a good set of mud flaps reduces the amount of grime your tires kick up onto your vehicle. You can also invest in wheel well liners for additional protection.

How Often to Wash the Undercarriage of a Car or Truck

Wash your undercarriage at least once a season, prioritizing spring, since it's a good time to remove anything that may have accumulated after a long winter.

You can also plan to wash your undercarriage as needed. For example, off-road trips, beach driving, and muddy roads can pack the undercarriage with dirt and sand that hold moisture against the metal. After an outing like this, shoot for an undercarriage wash, whether at home or with a quick run through the automatic wash.

How Often to Wash the Undercarriage in Winter

Expert advice varies by source, but try to wash your vehicle’s undercarriage at least every two weeks. For example, Husky Liners recommends washing every 10 to 14 days while salt is on the roads, while AAA recommends at least every two weeks.

An automatic wash membership makes that schedule easier to keep, and the more you use it in a given month, the more likely it is to pay for itself. Here in Detroit during the winter, with my local wash membership, I run my vehicle through every few days, including after a storm or any period where there is a brief thaw.  

Don’t Let Road Salt Have the Last Word

Road salt has kept roads clear since New Hampshire’s experiment in the winter of 1938, but it still takes a toll on the components underneath your vehicle. A regular undercarriage car wash is one of the best ways to mitigate that potential damage, whether you use an automatic tunnel wash with an underbody flush or clean it yourself in the driveway with the steps above.